Steel and metallurgy · Steel, foundries, rolling and forging

Stable Power for Processes That Cannot Stop

Flicker and harmonic control, substations, variable frequency drives and backup for critical services in plants with electric arc or induction furnaces and rolling mills. 18 years of EPC experience in heavy industry, with a single technical point of accountability.

Why a steel mill's electrical network is different

Few industrial loads punish the grid as much as a melting furnace. Added to this are high-power motors that start and stop continuously, and auxiliary services that cannot fail without putting the equipment at risk. These are the problems that cost the most in the plant:

Flicker and harmonics

The arc furnace demands reactive power erratically and the induction furnace injects harmonics. The result: voltage fluctuations, overheated transformers, protection trips, penalties and Grid Code compliance observations.

Demand peaks

Casts and large engine starts raise the maximum demand measured in the GDMTH rate. A single poorly managed peak is reflected in the capacity charge for the entire month.

Harsh environment for electrical equipment

Radiant heat, conductive metal dust and vibration accelerate the deterioration of boards, transformers, connections and motors. Failures appear earlier than the maintenance schedule indicates.

Unbacked critical services

If you lose cooling water from furnaces or hydraulics during a blackout, the damage is no longer just lost production: it is committed equipment and risk to the staff.

Where we intervene in the plant's electrical network

Simplified diagram of a typical steel mill or foundry. Each number is a point where VMS Energy designs, supplies, installs or maintains.

Simplified one-line diagram of a steel plant The high voltage network feeds the main substation, which in turn feeds a medium voltage bus. The bus outputs: the transformer and melting furnace with its SVC or STATCOM compensation, the rolling drives and motors, the auxiliary services motor control center with emergency plant backup, and a BESS storage system for peak trimming. Medium voltage bus CFE network · high voltage HV/MV main substation Oven transformer Arc furnace or induction SVC/STATCOM + filters variable frequency drives (VFDs) M Lamination, presses and forges MCC auxiliary services Cooling pumps, compressors, cranes, Dust collector G Emergency plant and UPS BESS Peak Trimming GDMTH 1 2 2 3 3 3 4 5
Illustrative diagram. The actual configuration (voltages, number of furnaces, type of compensation) is defined with the survey and electrical studies of each plant.
1

Energy quality in furnaces

Measurement of flicker, harmonics and unbalance; study and proposal of dynamic compensation (SVC or STATCOM) and passive or active filters.

Fewer shots, fewer penalties, and Network Code compliance.

Power quality →
2

Main substation and distribution

New MV/HV substations, expansions and ght; supply, testing and maintenance of transformers, including furnace; medium voltage switchgear, short circuit studies and protection coordination.

Ability to grow and selectivity so that a failure does not destroy the entire plant.

Subestaciones →
3

variable frequency drives, engines, MCC and pumps

Low and medium voltage variants, including regenerative for frequently braking loads; high-power engines; MCC under IEC 61439; and cooling and process pumps.

Smooth starts, fine speed control and braking energy recovery.

Variations → CCM →
4

Support of critical services

Criticality analysis of loads, emergency plants, industrial UPS and automatic transfers for oven cooling, hydraulics and control.

The equipment is protected even if the external supply fails.

Emergency plants →
5

Demand control

Load profile analysis and billing, power factor correction and energy storage (BESS) for peak trimming in GDMTH.

Lower capacity charge, evaluated with actual plant data.

BESS Savings Calculator →
+

Predictive maintenance throughout the plant

Thermography, dielectric oil analysis, transformer testing and motor condition monitoring, adapted to environments with heat and metallic dust.

Detect the fault before it stops a cast.

Predictive maintenance →

From the oven to the finished product

Electrical systems that support each stage of the process

01Fusion
Electric arc furnaceInduction furnacePot ovenReagent compensation
02Laundry
Continuous castingFoundry moldingCooling waterBridge cranes
03Formed
Reheating furnacesRolling trainsPresses and forgingHigh power variances
04Finishing and services
Heat treatmentCutting and machiningCompressed airDust collector

Start with an electrical and power quality diagnosis

Before proposing equipment, we measure. The diagnosis is carried out following the applicable standards at critical points and includes evaluation of flicker and harmonics against the applicable limits and the Grid Code, analysis of the demand and billing profile, and a review of criticality of loads and backup. You receive a technical report with findings, risks and recommendations prioritized by impact.

Experience in heavy industry, applied to steel

The electrical challenges of a steel mill are similar to those we already solve in other continuous process sectors: high-power loads, aggressive environments and very costly downtime. Some projects that support it:

Cement plant
Jalisco, Mexico
Major maintenance on a 69 kV substation in a continuous process plant.
Cement plant
Colima, Mexico
Engineering and integration of process control cabinets and supply of 12.6 km of medium and low voltage power cable, including the power supply to drives.
Mining operation
Durango, Mexico
Supply and commissioning of a 700 HP Altivar 980 variator for high-demand deep pumping.
Tamazula Sugar Mill
Jalisco, Mexico
Regenerative 300 HP variable with energy recovery, the same technology that applies in lamination loads that frequently slow down.
Cement and minerals
Mexico
Clients such as CEMEX, Holcim, Cemento Cruz Azul and IMERYS, with continuous operation and high power loads.
Energy and Oil & Gas
Mexico
Projects for PEMEX, CFE, Baker Hughes and SLB under strict safety, quality and documentation requirements.

Read the case of the regenerative drive →

How we work

EPC methodology with single responsibility, from measurement to support after startup, and with work windows coordinated with scheduled plant shutdowns.

01

Diagnosis and measurements

Electrical survey, power quality measurements and load criticality analysis.

02

Studies and engineering

Load flows, short circuit, protection coordination, electric arc and compensation sizing; basic and detailed engineering.

03

Procurement and construction

Multi-brand supply, electromechanical assembly and testing, programmed to take advantage of maintenance stops.

04

Commissioning and maintenance

Energization, verification measurements against the baseline and preventive and predictive maintenance programs.

Frequently asked questions — Steel and metalworking

The arc furnace demands reactive power in a highly variable manner, especially in the scrap melting stage. These rapid variations cause voltage fluctuations that are perceived as flicker and that can affect the plant itself and the network. It is corrected with dynamic compensation (SVC or STATCOM) combined with harmonic filters, sized from real furnace measurements.
Yes, but of another kind. Its power converters inject Aronics that heat transformers, trigger protections and affect plant electronics. An energy quality study defines whether passive, active filters or a combination are required.
Our background is in heavy industry with equivalent electrical challenges: cement, mining, oil & gas and sugar mills. That is why we propose to start with an electrical and power quality diagnosis in your plant: we measure, quantify the problem and present the technical proposal based on real data.
First, the load profile is analyzed to separate the controllable peaks from the process peaks. Depending on the case, power factor correction, auxiliary load management and energy storage (BESS) are combined to cut peaks in the GDMTH rate. Feasibility is evaluated with the plant's billing history.
Those that protect equipment and personnel in the event of a blackout: furnace and panel cooling water pumps, hydraulic systems, control and protections. They are supported by emergency plants, industrial UPS and automatic transfers, defined with a load criticality analysis.
VMS Energy has a certified Integrated Management System: ISO 9001 (quality), ISO 14001 (environment), ISO 45001 (safety and health), ISO 37001 (anti-sustaining) and ISO 50001 (energy).

An electric grid at the height of your furnaces

Power quality, substations, drives and backup for steel mills, foundries, rolling mills and forges throughout Mexico. We will contact you in less than 24 business hours.