Diagnosis
We lift load, route, environment and regulations.
Design and supply for substations, plants and mining.
Choose the degree of voltage and the arrangement, write the design current and the configurator returns the minimum section that supports it, with its diameter, its weight and its catalog ampacity. KEI factory data according to IS 7098 Part 2/1985.
The configurator covers up to 19/33 kV, which is the highest degree of these tables. For 66 kV and above, go to Extra high voltage cables (66–400 kV).
We pass requirements, define construction and ensure timely delivery.
We lift load, route, environment and regulations.
We define construction, testing and documentation.
We schedule deliveries and traceability control.
VMS Energy selects the optimal manufacturer according to the voltage level, sector, applicable standard, availability and timeline of your project. KEI Wires & Cables is our main strategic partner, but we work with the best manufacturers in the world when the project requires it.
Authorized representative for Mexico. MV/HV/EHV power, ESP cables for Oil & Gas, photovoltaics, instrumentation and control. First option for most industrial projects in Mexico.
Specialty in highly engineered EHV cables (German manufacturing). Ideal when the project requires European standards, VDE certifications or special constructions for extra high voltage transmission.
Solutions for control, testing and special applications: LSZH for confined spaces, EMC armored, high temperature (silicona), cables for food industry and robotics.
Domestic manufacturing under NMX-J. Low voltage and control with short delivery times. Ideal for projects with a required national component or emergencies in the field. NOM-001-SEDE compliance.
Through VMShop you can request a cable quote directly — with or without an EPC project. If the supply is part of an EPC project that VMS engineers and builds, the cable is integrated into the MTO with milestone logistics and single responsibility. If you only need the material, we also support you with the same technical rigor.
If you only need uninstalled supplies, we can also support you — with the same technical and logistical rigors we apply to our EPC projects.
Both insulations operate at 90 °C in normal regime and 250 °C in short circuit. The difference is in the environment and the type of application.
| Criterion | LCA | EPR |
|---|---|---|
| Dielectric strength | Superior | Good |
| Flexibility | Minor | Superior |
| Mobile equipment (trailing) | ✗ Not recommended | ✓ Ideal |
| Humid environments | Good | Better |
| Substations and fixed lines | Ideal | Supported |
| Relative cost | Minor | Major |
| VMS Recommendation | Substations, main feeders, fixed medium voltage lines | Mining (trailing cables), moving equipment, environments with severe humidity |
Terms like LCA, EPR, MV, U0/U, FRYRING CABLE o NMX-J? Consult them in the Cable technical glossary
Operating voltage (U0/U in kV), total length per circuit, type of installation (band, duct, buried), ambient temperature of the site, required standard (IEC, NMX-J, CFE) and delivery schedule. With this data we contact you in less than 24 hours; the time of the quote depends on the scope.
Depends on the application. XLPE is ideal for fixed installations, substations and main feeders. EPR is superior in mobile equipment (trailing cables in mining), high humidity environments and applications that require greater flexibility. Consult the Selection guide from this page or ask us for technical advice.
Yes. Condumex and Viakon (national manufacturing under NMX-J) are available for low voltage and control when the project requires national component, short delivery times or NOM-001-SEDE compliance. For medium and high voltage, KEI and Südkabel are the reference manufacturers.
Yes. Delivery by milestones is our standard in EPC projects. We coordinate supply schedule, coil traceability, technical documentation by batch and check of the personal data of the company before installation.
Factory test certificate (individual and type tests), cable data sheet, length report per coil, traceability labeling and, if the project requires it, specific documentation for CFE, PEMEX, ISO audits or health audit in the food industry.
Both options are available. As an EPC contractor, we integrate supply, installation, testing and commissioning under a single contract. If the project already has an installation contractor, we can act only as a technical supplier with the same rigor.
Grupo Sáenz — Ingenio Tamazula
Jalisco
Engineering, supply, installation and channeling of 4.1 kV medium voltage cable from the distribution board to the generator.
Cement plant
Colima
Supply of 12.6 km power cable in medium and low voltage, including variable frequency drive power supply.
Maritime Services Campeche / Pemex
Campeche
Preparation of relief cones and testing of power cables at 4.16 kV, with preparation of terminals and sleeves.
EK-A Platform — Pemex
Campeche (offshore)
Preparation, installation and interconnection of medium voltage terminals for the power circuits of the generation system.
BALAM-A Platform — Pemex
Campeche (offshore)
Preparations, installation, hypot testing and interconnection of heat shrink terminals and relief cones.
Pemex
Tabasco
Channeling of medium voltage wiring from the drive to the distribution board, and channeling and wiring for an electrocentrifugal pump, on a marine platform.
Quote directly with our technical team. On-site delivery, custom cutting and application support.