EPC Agroindustry · Projects from $1,000,000 MXN

Electrical Engineering for Sugar Mills and Agribusiness

Woodward turbine-generators, MV/HV substations, process automation and predictive maintenance for sugar mills in Mexico, during both the harvest and maintenance seasons.

Governors Woodward 505/2301 Substations 13.8–69 kV Process automation
12+
sugar mills
10
states of the Republic
18
years in the sector
24 hours
zaffra response
EPC
design-construction
Challenges in the sector

The electrical pressure that every director of a sugar mill faces

The sugar industry operates under conditions that have no equivalent in other sectors: rigid seasonality, short maintenance windows and a cost of unemployment during the harvest that can exceed $500,000 MXN per hour.

01

Electrical seasonality without margin of error

During the harvest (November–May), the power plant operates at 100% capacity, 24 hours a day, for six continuous months. A failure in the turbogenerator, substation or Woodward governor can cost between $50,000 and $500,000 MXN per hour of lost production. There is no second chance: the cut cane deteriorates in hours and the grinding schedule cannot be recovered.

02

Massive starts in pre-harvest

At the beginning of the season, the mill starts dozens of high-torque motors—mills, diffusers, steam pumps, evaporators—in a few hours. Poor coordination of protections, a poorly configured drive or a faulty synchronization switchgear can generate chain trips that stop the entire factory right on start-up day. The pre-harvest is the time of greatest electrical risk of the year.

03

Short window for projects and investment

Repair (May–October) is the only window to execute important electrical projects: substation rehabilitation, updating of governors, installation of new CCMs or cables. If imported materials are delayed or engineering is not ready, the harvest starts with substandard equipment — and the next repair cycle is six months away.

Our solutions

Electrical services for sugar mills

The sugar industry has critical electrical requirements: own generation with turbosteam, interconnection substations with CFE and intensive maintenance during repair. VMS Energy covers the entire spectrum.

Steam Turbogenerators — Woodward

Programming and commissioning of Woodward 505, 505-XT and 2301D governors for counterpressure and extraction-condensation turbines. PID loop adjustment, overspeed test and synchronization with CFE network. Experience in more than 12 mills throughout Mexico.

MV/HV power substations

Design, construction and rehabilitation of 13.8–69 kV substations for sugar mills. Acceptance tests (TTR, VLF, contact resistance), synchronization switchgear for parallelism with CFE and major maintenance of transformers and switches.

Power plant automation

SCADA integration of the mill's power plant: monitoring of generation, distribution and consumption. Automation of process equipment: mills, diffusers, evaporators and centrifuges. Updating obsolete boards to modern PLCs with industrial Ethernet communication.

Predictive maintenance in repair

Electrical Thermography of Boards, MCC and Substation. Transformer Diagnostics (TTR, megger, DGA) during the annual repair stop. VLF test on MV cables to evaluate insulation status before the next harvest.

MCC and force distribution

Supply and installation of IEC 61439 Motor Control Centers (MCC) for factory, batey and cogeneration areas. Updating of mechanical starters to frequency variable frequency drives for energy saving in pumps and fans.

Power factor correction

Study of measurement, design and installation of APFC banks to correct the power factor before CFE and avoid penalties. Mills with high motor and furnace loads can reach FPs of 0.75–0.82, generating significant additional charges.

Seasonality of the sector

Electric cycle of the sugar mill

The sugar industry operates in defined annual cycles. VMS Energy accompanies the mill at each stage with the appropriate electrical services to maximize availability during the harvest.

Repair (May–Oct)

Major maintenance of turbines, governors and substation. Thermography, VLF, transformer diagnosis. Updating boards and MCC. Ideal time for EPC projects.

Pre-harvest (Oct–Nov)

Commissioning of Woodward turbogenerators and governors. Switch and switchgear testing. Adjustment of electrical protections. SCADA verification and control systems.

Zafra (Nov-May)

Emergency technical support, 2007. Response in less than 24 hours to failures in governors or electrical systems. Unscheduled stoppage costs between 50,000 and 500,000 BDN per hour.

Closing of the harvest (Apr–May)

Analysis of electrical performance of the harvest. Identification of improvements for the next season. Investment planning and repair projects.

Ingenuities served

Our history in the sugar industry

Presence in sugar mills in the main sugar producing states of Mexico: Veracruz, Morelos, Oaxaca, Jalisco, Michoacán, Tabasco, Campeche and San Luis Potosí.

Ingenio San Nicolás

Veracruz

Advice, supply and commissioning of the electrical load distribution panel of the new plant, including synchronization with CFE with import and export.

Ingenuity Emiliano Zapata

Morelos

Commissioning of a 2301D-ST governor with Valtek 50 actuator in turbogenerator 1, and subsequent modernization of the speed control with Woodward 505 electronic governor.

Ingenio Adolfo López Mateos

Oaxaca

Change of the 2301D-ST for a Woodward 505 Enhanced governor in turbogenerator 1, and start-up of the cogeneration system synchronization switchgear with MSCL II and DECS 250 on the control panel.

Santa Rosalía Sugar Mill

Tabasco

Commissioning of a Woodward 505 governor on turbogenerator 2, with supply and installation of a Valtek 50 actuator.

Santa Clara Sugar Mill

Michoacan

Supply, installation and commissioning of a Governor Woodward 505 at the NEB TG1 Turbogenerator, with adaptation of a new UG40 actuator; then modernization of turbine speed control and generation plant.

Three Valleys Mill

Veracruz

Increase in operational capacity in electrical substations no. 2 and no. 5, the latter in 4 160 V, and modification of the Electrobús BUS "C", all with electrical tests.

Tamazula Sugar Mill

Jalisco

Mechanical turbine service with dynamic balancing and blade and arrow testing; maintenance, installation and commissioning of speed governors; and a regenerative variator of 300 HP from Schneider Electric.

Ingenio Casasano

Morelos

Modernization of speed control for steam turbine with Peak 150 and Woodward PG-PL actuator.

Ingenuity of Autlán

Jalisco

Manufacture of bases for the speed governor, maintenance and commissioning.

Ingenio La Joya

Campeche

Supply, calibration and commissioning of Woodward's 2301 and 505 electronic speed governors, and supply of the Basler Electric DECS 250 excitation system.

Ingenuity The Bee

Morelos

Modernization of the speed control of a mill turbine with Peak 150.

Ayala Plan Ingenuity

San Luis Potosi

Commissioning of a 2301D-ST governor with CPC-1 actuator in turbogenerator 3.

Ingenio José María Morelos

Jalisco

Service tuning the automatic voltage regulator DECS from Basler Electric.

Why VMS Energy?

Advantages of working with VMS in the sugar sector

We understand the pressures of ingenuity: the harvest does not wait, unscheduled stoppages are devastating and engineering must be precise from the first attempt.

Response within 24 hours

During the harvest, we have an engineer available to travel to any point in the republic in less than 24 hours. Every hour of unemployment costs.

In-depth knowledge of the process

We understand the relationship between process steam generation and electricity generation. Our engineers have worked in more than 12 different mills.

EPC comprehensive service

From substation design to governor commissioning, we offer a single point of contact for all mill electrical engineering.

Woodward 505 / 2301D Substations 13.8–69 kV NETA MTS Thermography VLF cables MV SCADA Automation MCC IEC 61439 FP Correction NOM-001-HEADQUARTERS
Frequently asked questions

What the technical directors of sugar mills ask

The cost of an unscheduled stoppage varies between $50,000 and $500,000 MXN per hour, depending on the size of the mill and the price of sugar. It includes loss of ground cane, start-up costs, possible damage to process equipment and penalties with cane suppliers. A predictive maintenance program during repair has an ROI of months, not years.
Major maintenance must be performed during the annual repair (May–October): substation tests (TTR, VLF, megger on MV cables), transformer maintenance, protection adjustment, MCC and panel review, and complete servicing of Woodward governors and turbogenerators. During the harvest, predictive monitoring (thermography, vibration analysis) is carried out without major intervention.
Yes, it is our specialty. We work with schedules adjusted to the repair window (usually June–October). We coordinate engineering, supply and construction to ensure that the power plant is ready before pre-safra start in November. The key is to start engineering detail at least 3 months before the start of repair to ensure delivery of the equipment. import equipment.
The Woodward 505 is an advanced digital controller for steam turbines with extraction, backpressure and synchronization control with CFE network. The 2301D is more compact, ideal for turbines up to ~5 MW in isochronous or droop mode. It is advisable to update when the mechanical governor no longer has spare parts, when there is speed instability (hunting) or when integration with SCADA is required. Upgrading to digital improves speed stability from ±3% to ±0.5%.
The mills must comply with NOM-001-SEDE (electrical installations), NOM-029-STPS (facility maintenance), IEEE C37 (protection in generation systems), IEEE C57 (power transformers) and the CFE requirements for interconnection of own generation according to the Electrical Industry Regulations. SADER may require technical documentation of electrical installations in mill certification audits.
Through three levers: (1) replacement of mechanical starters with variable frequency drives in pumps and process fans (typical savings 15–30%), (2) power factor correction with APFC banks to eliminate CFE penalties and reduce cable losses (ROI 12–24 months), and (3) MCC upgrade with per-circuit consumption monitoring to identify oversized equipment.

Are you planning electrical projects for the next repair?

The best time to plan is now. Contact us for an evaluation of your electrical plant and a quote for repair services and the next harvest.

Request plant evaluation
Contact specialist